CONNECT WITH US
Just Add Power
West Penn Wire
Join our mailing list!
ESE 100 Minute 1/2 Inch High Yellow Digit Up/Down Timer Black
List Price: $435.00
You save $24.29!
Usually Ships in 3 to 5 Business Days
The ES 301U and ES 380A are presettable 100-minute Up/Down Timers. Units are "preset" by advancing the proper digit using the "Min-Set" or "Sec-Set" control. The ES 380A has 1" high yellow LED displays and is controlled via rear mounted connectors, while the ES 301U has .55" high yellow LED displays and has six front mounted controls.
.55" Yellow LED Display
100 Minute Up / Down count range (00:00 - 99:59)
Up, Down, Stop, Min-Set, Sec-Set & Reset functions
Optional Remote Control input
220-240 VAC (110-120 VAC is standard) & UL options available
Various Options available: Black(7), C, D, J, N, P, P2, Q, R, ESE, T, UL, W, Y, Z
10nS Accuracy: The accuracy of the unit is improved to 10nS.
Black Anodized Front panel-option availabel when standard panel is clear anodized
Crystal Time Base (2-3 seconds per week accuracy)
ESE Serial Time Code Output
External Input of either 1 MHz, 5 MHz, or 10 MHz (for use with "in-house" Standard)
IRIG-B or IRIG-E Time Code may be specified (not available with SMPTE/EBU)
NPR (National Public Radio) Time Code INput (excluxive) with ESE Time Code Output
NTP Client Display will synchronize exclusively with an NTP server
Six-Digit Display: A 6-Digit (Hr, Min & Sec) Front Panel Mounted Display (.55" LED) is provided. Option 'P' is required.
Nine-Digit Display: A 9-Digit (Days, Hr, Min & Sec) Front Panel Mounted Display (.55" LED) is provided. Option 'P' is required.
GPS Antenna: High Performance GPS Antenna for harsh RF Environments.
Parallel BCD Output: CMOS compatible, 5-volt logic in parallel four-line format. Specify the ES-169B.
Battery Back-Up: An internal Gel-Cell battery is provided capable of maintaining the unit's microprocessor for up to a 4-hour power outage.
Time Zone Offset via internal DIP Switch
9" x 3 1/2" Front Panel for Console Mount Applications (Case is 8" Deep)
RS232C ASCII Computer Interface (RS422A available on a custom basis)
"UL" Approve Wall Mount Power Supply
DC Power (12 VDC)
3-Wire Line Cord (2-Wire Line Cord is Standard on many units)
Wall Mount Enclosure replaces standard enclosure
DC Operation: Requires the unit to be powered from a DC source exclusively, typically +12 to +35 VDC.
SMPTE or EBU Time Code outputs: SMPTE or EBU Time Code outputs may be specified (not available with IRIG).
Relay Closure: Option "HR" provides a user programmable relay contact closure. The standard contact closure occurs on the Hour and Half Hour. If contact closures at other times are desired, the user can program up to four relay closures using the PC Software, which can be downloaded from the ESE web site. The reed relay is rated at 10 watts maximum resistive load (500 mA switching current) and is intended for control applications only. The relay contacts are accessible on the DB-9 connector.
220 VAC/50 Hz Operation: The unit is configured to operate from 220 VAC line voltage. 117 VAC 50/60 Hz is standard.
provides a 10 MHz output and a 1 KHz output. Option '10ns' is required if option 'K' is specified. UL "UL" Approved Power Supply: The unit is supplied with a UL/CSA approved wall mount power supply.
1) Included at no charge
2) Specify ES-362U if Option 'R' is required
3) 'Q' can only be ordered if Option 'D' is included
4)Options 'N' or 'Y' or 'N' and 'Y' can be ordered at $125 (ES-370 & ES-371)
5)LX 192U/LX 194U or ES 192U/ES 194U must be ordered if any of these options are req'd. Serial output is supplied at no charge.
6)'T' is substituted as follows: LX/ES 361UT= LX/ES 161U; LX/ES 366UT = LX/ES 166U; ES 364UT = ES 943U; ES 369UT = ES 996U/Amber; ES 372UT = ES 171U, ES 570T = 570UT
7) Available only if Option 'P' or 'Q' is specified; or, if Wall is specified on the ES 391A or ES 590A.
8) Voltage on ES 370, ES 371, & ES 570 is 5 volts; all others is 12 volts (including Option 'T' on ES 570U)
9) With option 'SV' only one of the following options may be specified 'L2', 'L4', or 'P2'
10) Includes Windows© Software
11) ESE time code output option may be specified if ordering 'NTP' option
12) Not available with option 'Wall'
13) Specify the ES-991U/NTP for a 2.3" display or the ES-941U/NTP for a 4.0" display
NOTE: PLEASE CALL BEFORE ORDERING FOR CUSTOMIZATION!! THANK YOU
Share your knowledge of this product with other customers...
Be the first to write a review
Browse for more products in the same category as this item:
Studio & Set Gear
Clocks, Timers & Stopwatches
Studio & Set Gear
Copyright © 2011-2014 www.3DHDgear.com. All Rights Reserved.